Wet Rot Treatment

Guide · Homeowners · 3 min read · Updated 17 November 2026

Rotten Window Sill: Repair with Resin or Replace It?

Short answer

If the rot is limited to part of a sill or frame and the surrounding timber is sound, a resin repair at £120–£350 per window is usually the best value and keeps original joinery. If the sill is rotten through its depth or along most of its length, replacing it at £250–£550 is better. Whole-window replacement is only needed when frames and sashes are widely decayed.

Rotten Window Sill: Repair with Resin or Replace It?

Why sills rot first

Window sills and the bottom rails of sashes and casements take the brunt of the weather. Rain runs down the glass and collects on the horizontal surfaces, and if paint cracks or putty fails, water soaks into the end grain and joints. The timber stays wet for long periods, which is exactly the condition wet rot needs. The bottom corners, where the sill meets the frame, are usually the first places to go soft.

Missing or blocked drip grooves under the sill make things worse, because water runs back along the underside and into the wall instead of dripping clear.

Inside, condensation running off the glass onto the window board can cause the same problem from the room side, particularly in bedrooms and bathrooms.

How to judge the damage

Press a screwdriver or bradawl into the timber at several points along the sill and around the frame joints. Sound timber resists firmly. Decayed timber gives way, feels spongy or breaks up into fibres. Pay close attention to the ends of the sill, the joints with the frame and the bottom rail of each sash. Note how deep the screwdriver goes and how far along the softness extends.

Look at the paintwork too. Cracked or flaking paint, open joints and dark staining are all signs that water is getting in. Check inside as well, because damp patches or mould on the window board and wall below can mean the sill has failed.

  • Probe sill ends, frame joints and bottom rails
  • Note depth and length of soft timber
  • Look for cracked paint, open joints and dark staining
  • Check the drip groove under the sill is clear
  • Inspect the inside window board and wall below

Repair or replace: how to decide

The decision usually comes down to how much sound timber is left. Resin repairs are ideal where the decay is local, for example a corner of the sill or the end of a bottom rail, and the rest of the timber is solid. Replacement makes sense where the sill is soft right through or along most of its length, because there is not enough sound wood for the resin to bond to and support.

Think about the age and value of the window too. An original Victorian sash made from dense, slow-grown timber is usually worth repairing even when the damage is significant, while a modern softwood casement with widespread decay may be better replaced. A joiner can advise on which approach gives the best long-term value for your window.

SituationBest optionTypical price
Local soft patch, rest of sill soundResin repair£120–£350 per window
Sill rotten through or along most of its lengthSill replacement£250–£550
Frame feet rotten, rest of frame soundSplice or resin repair£120–£350 per window
Frames and sashes widely decayedConsider whole window replacementQuoted separately

How a resin repair works

The decayed timber is cut and scraped out back to sound wood. The remaining timber around the cavity is treated with a liquid wood hardener, which soaks in and binds weakened fibres. A two-part epoxy filler is then pressed into the void and built up slightly proud of the surface. Once cured, it is shaped to match the original profile, primed and painted.

Done properly, resin repairs are durable and flexible enough to move with the timber. They are particularly useful on period windows, where replacing a whole sill or frame would mean losing original joinery. They are not a substitute for maintenance. The repaired area still needs good paint and sound putty to keep water out.

How a sill replacement works

With the frame left in place, the old sill is cut out in sections and the new sill made to match the profile, usually from pre-treated softwood or a durable hardwood. It is fitted under the frame, joined securely and sealed, with a drip groove on the underside. The new timber is primed on all faces before fitting, which helps it resist moisture, and then painted.

Replacement takes longer than a resin repair and is more disruptive, but it gives a new, sound timber that should last many years with maintenance.

Ask the joiner to check the frame joints and the bottom of the sashes at the same time, as they are often affected too and are easier to repair while the window is already being worked on.

Period windows, listed buildings and regulations

In listed buildings and many conservation areas, there are controls on replacing original windows, so repair is often preferred and consent may be needed for replacement. Resin repairs and sill replacements that match the original are usually the most acceptable approach. Check with the local planning authority before replacing any window in a listed building.

Like-for-like repairs to existing windows do not need building regulations approval. Replacement windows in England and Wales, however, must meet the Building Regulations, usually certified through a competent person scheme or building control. That is worth knowing if your repair turns into a replacement.

Questions people also ask

How long does a resin window repair last?

A well-executed resin repair can last many years, provided the window is kept painted and the putty and joints stay sound. Epoxy resins are designed to move with the timber and resist moisture. The main risk of failure is water getting into the surrounding timber through neglected paintwork.

Can I replace just the window sill?

Yes. A joiner can cut out the old sill and fit a new one with the frame left in place. This is common on both sash and casement windows. It costs £250 to £550 depending on the size and timber used, and avoids the cost and disruption of a new window.

Is it worth repairing old timber windows?

Often, yes. Older windows were frequently made from dense, slow-grown timber that lasts well when maintained. Repairing them keeps original character, can be cheaper than replacement and is often preferred in listed buildings and conservation areas. Draughtproofing and secondary glazing can improve comfort without replacing the window.

Written and checked by the Wet Rot Treatment team. Read our editorial policy.

Get a free wet rot treatment quote

Tell us what you need and we'll come back with a clear price.

Request a quote